Product Specs
General Specifications
- Maximum Rating
- 300 BHP
- Displacement
- 441.8 in³
- Minimum Rating
- 225 BHP
- Governor and Protection
- Electronic (ADEM™ 3)
- Aspiration
- Turbocharged-Aftercooled
- Flywheel and Flywheel Housing
- SAE 1, 2, or 3
- Flywheel Teeth
- 156 (SAE 1), 134 (SAE 2), 126 (SAE 3)
- Rotation from Flywheel End
- Counterclockwise
- Stroke
- 5 in
- Bore
- 4.3 in
Emissions
- Emissions
- EPA & CARB Non-Road Tier 3, EU Stage IIIA, IMO Tier II
Dimensions
- Length
- 41.4 in
- Width
- 29.9 in
- Height
- 40.6 in
- Weight
- 1386 lb
Capacity for Liquids
- Lube Oil System - Refill
- 4.8 gal (US)
Standard Equipment
-
- Air Inlet System
-
- Turbocharger, air to air aftercooled
- Air inlet, LH side facing front 79.0 mm (3.11 in) connection
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable rating
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Programmable monitoring system (engine speeds, temperature, pressure)
- J1939 broadcast (diagnostic and engine status)
- Automatic variable timing, electronic
- All engines shipped at max rated rpm
-
- Cooling System
-
- Thermostats and housing, vertical outlet
- Jacket water pump — belt-driven, centrifugal
- Water pump, inlet RH front vertical inlet (pointing down)
-
- Exhaust System
-
- Exhaust manifold — dry
- Front turbo exhaust
-
- Fuel System
-
- Hydraulic Electronic Unit injection (HEUI)
- Fuel filter — secondary, LH front (2-micron high performance)
- Fuel transfer pump — LH front
- Fuel priming pump — LH front
-
- General
-
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Electronic installation kit (connectors, pins, sockets)
-
- Lube System
-
- Crankcase breather, LH side
- Oil cooler, RH
- Oil filler, front top valve cover
- Oil filter and sampling valve, RH
- Oil pan, front sump, 31 L (33 qt) oil change capacity
- Oil dipstick, LH rear
- Engine oil pump (gear-driven)
- Engine shipped without oil
-
- Power Take-offs
-
- Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (0.88 in) wide
Attachments
-
- Air Compressor
-
- Air compressors
- Air compressor governor
-
- Air Inlet System
-
- Air cleaners
- Precleaner
- Air inlet elbow
- Air shutoffs
-
- Charging Systems
-
- Charging alternators
- Alternator mountings
- Alternator belt tensioner
- Alternator pulleys
- Alternator guards
-
- Cooling System
-
- Radiators
- Fan drive and pulley - f/u/w radiator packages
- Fans f/u/w radiator packages
- Coolant level sensor
- Fan drive mountings
- Fan adapters
- Fan adapter for blower fans
- Fan pulleys
- Fan height instructions
- Vee belts for customer-supplied radiators
- Suction fans and blower fans
- Water inlet elbows
- Dry charge coolant conditioners
-
- Emissions Certification
-
- IMO Certification
-
- Exhaust System
-
- Flexible fitting
- Turbocharger exhaust outlet adapters
- Elbows, flange, pipes, clamp
- Rain caps
- Manifolds
- Mufflers
-
- Flywheels And Flywheel Housing
-
- Crankshaft seal
-
- Fuel System
-
- Flexible fuel lines
- Water separator and fuel filters
- Fuel cooler
-
- General
-
- Tool set
-
- Instrumentation
-
- Gauges and instrument panels
- Interconnect harnesses
- Voltmeters
- Gauge mounting
- Ammeter
-
- Lube System
-
- Oil pan
- Drain and cover
- Oil level gauges
- Remote oil filter
- Oil fillers
- Lubricating oil
- Fumes disposal
-
- Mounting System
-
- Structural steel base
- Front engine support
- Rear engine supports
-
- Power Take-offs
-
- Enclosed clutch
- Clutch supports
- Flywheel stub shaft
- Hydraulic pump drives
- Hydraulic gear pumps
-
- Starting System
-
- Starting Aids
- Electric Starting Motors — 12V and 24V
- Battery Sets - 12V and 24V (dry)
- Battery Cable