C18 ACERT Land Mechanical Drilling Engine

Request Quote

Download a Product Brochure

Please contact your nearest store for rates and other details.

Product Specs

Engine Specifications

Maximum Rating: 700 BHP
Emissions: EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA
Displacement: 1100 in³
Minimum Rating: 575 BHP
Bore: 5.7 in
Stroke: 7.2 in
Rated Speed: 2100 r/min
Aspiration: Turbocharged-Aftercooled
Governor and Protection: ADEM A3
Engine Weight - Net Dry: 2807 lb
Rotation from Flywheel End: Counterclockwise
Oil Change Interval: 250
Flywheel and Flywheel Housing: SAE No. 0 or SAE No. 1
Flywheel Teeth: 136 (SAE 0), 113 (SAE 1)

Capacity for Liquids

Minimum Cooling System - Engine Only: 13.2 gal (US)

Dimensions

Length: 54.7 in
Width: 36.2 in
Height: 49.5 in

Standard Equipment

Air Inlet System
- Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hoseconnection
- Dual turbocharger, front and rear inlet 127.0 mm (5 in.), hoseconnection
Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring and protection system (speed, temperature,pressure)
- J1939 Broadcast (diagnostic, engine status, and control)
Cooling System
- Thermostats and housing — outlet vertical
- Jacket water pump — gear-driven, centrifuga
- RH front water pump inlet
- All plugs/fittings are STOR for lines gp water
Exhaust System
- Exhaust manifold — dry
- Single turbo — front-facing turbo exhaust, full marmonconnection, maximum load 10 kg for direct connection to turbo
- Dual turbo — exhaust elbow, dry 203 mm (8 in)
Flywheels And Flywheel Housings
- See Mandatory Options
Fuel System
- Electronic unit injector
- Fuel filter, secondary, mid-mount (LH 2 micron high performance)
- Fuel transfer pump, LH front
- Fuel priming pump, LH mid-mount
- Fuel sample valve, mounted on fuel filter base.
Lube System
- Crankcase breather — rear valve cover
- Oil cooler — RH (dual)
- Oil filter — RH, LH
- Oil pan — front sump
- Oil dipstick — LH front
- Oil pump
Mounting System
- Front support (shipping only)
Power Take-offs
- Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm(11.5 in) 1 groove, all 15.9 mm (.63 in) width
- Hydraulic pump drive, SAE A, 11-tooth
General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit 70-pin connector (connectors, pins,sockets)
Mandatory Options
- Throttle position sensor
- Single turbo only — exhaust system (front or rear)
- Flywheel housing or rear PTO
- Primary filter/water separator

Attachments

Air Compressor
- Air compressor governor
- Expansion chambers
Air Inlet System
- Air cleaners
- Air lines
Charging System
- Charging alternators
- Alternator mountings
- Alternator wiring
- Circuit breakers and mountings
- Alternator belt guard
Cooling System
- Radiator
- Fan drive with radiator packages
- Fan height instructions
- Vee belts
- Aftercooler lines with Caterpillar installed radiator
- Single turbo configuration rear-facing exhaust
- Single turbo configuration rear-facing exhaust
- Aftercoooler lines
- Suction fan adapters
- Blower fan adapter
- Blower fan
- Suction fan
- Fan belt
- Coolant level sensor
- Dry charge coolant conditioners
Exhaust System
- Turbo exhaust connection
- Flexible fittings
- Elbows, flange, clamp, pipes
- Exhaust adapters
- Manifold
- Mufflers
Fuel Systems
- Flexible fuel lines
- Fuel filter location
- Fuel cooler
- Water separator
Instrumentation
- Gauges and instrument panels
Lube System
- Oil pans
- Drain and cover
- Oil level gauge
- Remote oil filters
- Oil filters
- Lubricating oils
Mounting System
- Structural steel base
- Front and rear engine support
Power Take-offs
- Rear enclosed clutches
- Hydraulic pump drives
- Hydraulics gear pumps
- Clutch supports
- Crankshaft pulleys
Protection System
- Air shutoff
Starting System
- Air starting motors
- Air pressure regulator
- Air silencer
- Start switch
- Electric starting motors — 12V, 24V
- Battery sets – 24V
- Battery cable and rack
- Starting aids
Transmission Arrangement
- Transmission water lines

Pin It on Pinterest