C27 ACERT Land Mechanical Drilling Engine
Exterior View
Please contact your nearest store for rates and other details.
Product Specs
Engine Specifications
- Maximum Rating
- 1150 BHP
- Emissions
- U.S. EPA Non-road Tier 2
- Displacement
- 1658 in³
- Minimum Rating
- 800 BHP
- Bore
- 5.42 in
- Stroke
- 6 in
- Aspiration
- Turbocharged-Aftercooled
- Governor and Protection
- ADEM A3
- Engine Weight - Net Dry
- 6382 lb
- Oil Change Interval
- 250
- Rotation from Flywheel End
- Counterclockwise
- Flywheel and Flywheel Housing
- SAE No. 0 or SAE No. 1
- Flywheel Teeth
- 136 (SAE 0), 113 (SAE 1)
Capacity for Liquids
- Minimum Cooling System - Engine Only
- 14.5 gal (US)
Dimensions
- Length
- 75.5 in
- Width
- 57.6 in
- Height
- 52 in
Standard Equipment
-
- Air Inlet System
-
- Dual turbochargers side or rear mounted — inlet 152.4 mm (6 in.) hose connection
-
- Control System
-
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring and protection system (speed, temperature, pressure)
- J1939 Broadcast (diagnostic, engine status, and control)
-
- Cooling System
-
- Thermostats and housing — outlet LH vertical orientation
- Jacket water pump — gear-driven, centrifugal RH
-
- Exhaust System
-
- Exhaust manifold — dry, heat shields
- Dual turbo — rear turbo exhaust, full marmon connection 127 mm (5 in.), maximum load 10 kg for direct
- Water-cooled center sections
-
- Flywheels And Flywheel Housings
-
- SAE No. 0 or SAE No. 1
- SAE standard rotation
-
- Fuel System
-
- MEUI system
- Fuel filter, RH ( 2 micron high performance)
- Fuel transfer pump
- Fuel priming pump (optional electric priming pump)
-
- Lube System
-
- Crankcase breather — rear mounted
- Oil cooler — RH
- Side turbo — oil filler in RH front gear case
- Rear turbo — oil filler in RH valve cover
- Oil level gauge — RH
- Oil filter — RH
- Oil pan rear sump
-
- Mounting System
-
- Front support — narrow
-
- Power Take-offs
-
- Crankshaft pulley — 203.2 mm (8 in), 5 grooves 15.9 mm (.63 in) wide; 292.1 mm (11.5 in.) 1 groove 15.9 mm (.63 in.) wide
-
- General
-
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit 70-pin connector (connectors, pins, sockets)
Attachments
-
- Air Inlet System
-
- Air lines
- Air cleaners
- Precleaners
-
- Charging System
-
- Battery chargers
- Charging alternators
- Alternator mountings
-
- Circuit Breakers
-
- Circuit breaker mounting
-
- Cooling System
-
- Blower fans
- Suction fans
- Radiators
-
- Exhaust System
-
- Muffler
-
- Fuel Systems
-
- Electric fuel priming pump
-
- Instrumentation
-
- Gauges and instrument panels
-
- Lube System
-
- Lubricating oil
- Oil pan
- Oil filter
-
- Mounting System
-
- Engine supports
-
- Power Take-offs
-
- Hydraulic pump drives
- Pulley
- Auxiliary drive
-
- Starting System
-
- Electric starting motor
- Battery sets - 24V
- Battery cable
- Battery rack
- Starting aids
-
- Packaging
-
- Overseas preservation
- Storage preservation
- Export packaging